sales (at) mp-molds.com

Free worldwide shipping on all orders over €399

6cav 02.23

Assembly of our mold

Check out this video about our molds and our dedication to perfection, and see how an MP mold is assembled. Looking for a mold? Browse our CNC-machined bullet molds.

tips and tricks MP-molds.com

Tip on easier release of HP pins

A simple trick for easier release of hollow point pins. Tip: take a soft graphite pencil and “paint” the part of the HP pin that comes in contact with the lead. More casting tips: General advice for using brass HP (hollow point) moulds.

6 good bases 314140 MP Molds Sledgehammer 6

General advice for using brass HP (hollow point) moulds

A practical guide to casting with brass hollow point moulds: from cleaning and heat cycling a new mould to finding the right casting rhythm. By experienced caster Gregor Hodnik (Gamsek). Quick reference Alloy: wheel weights + pure lead (50/50) with 2% tin. For powder coating: pure lead with 2% tin. Alloy temperature: 750F / 400C for rifle HP, 680F / 360C for non HP pistol moulds. A guidance, not a rule. Preheat: on a hot plate with the pins inserted, 20–30 minutes for long HP pins. Rhythm: fill, count to 3, open the sprue plate, count to 3, open the mould and dump. 1. Before the first casting Clean and assemble Clean the mould with brake cleaner, including the pins and the screws that hold them. (Warm water works too, but Miha already removes oils and debris before shipping.) Assemble the mould with the HP pins you want to use. Back the HP pin screws off about 1/8 turn, so the pins don’t bind in the mould. Heat cycle a new brass mould Put the assembled mould (pins inserted) on a hot plate set a bit over half power and bring it to about casting temperature. Switch the hot plate off and let the mould cool by itself. Repeat three or four times. No need to take the mould apart. This starts building the patina, and casting keeps it growing. Patina prevents sticking, so bullets generally drop out. Lube the right spots Lube the screws that hold the HP pins and the pins that hold the mould in the handles. Optionally coat the HP pins with a graphite pencil, only the part that forms the hollow point. Repeat every 4–5 sessions. Put a single drop of sprue plate lube (included with your MP mould) on the shafts on the outside of the blocks. Just a drop, so the cavities stay clean. 2. Casting with an HP brass mould Preheat on a hot plate Heat the mould on a hot plate (slightly over medium) until it reaches casting temperature or the sprue plate lube starts to smoke a bit. This saves many warm-up pours: a properly preheated mould needs only 3–5 fills, and a non HP mould can be perfect from the first pour. Tip: the longer the pins and the larger the hollow point, the longer the preheat. The pins must reach temperature too, usually 20–30 minutes, while your furnace heats up. Add tin to the alloy Tin helps hollow point bullets expand and fills out an HP mould well. Gregor uses wheel weights + pure lead (50/50) with 2% tin in the final mix. If you powder coat, you can simply use pure lead with 2% tin. Temperature and pouring With a bottom-pour PID furnace: 750F / 400C for rifle HP, 680F / 360C for non HP pistol moulds. If the pins cool down, problems start. Especially at the beginning, fill the cavities generously, front to back, to keep the heat in. A hot pin is a trouble-free pin. You can raise the alloy temperature and balance overheating with your casting speed. Once you find the happy medium, casting becomes a pleasure. When bottom pouring, don’t pour straight onto the pins. Aim slightly off center so the alloy doesn’t hit and cool the pins. The longer the pin, the more important this is. Cutting the sprue After pouring, watch the lead change colour as it solidifies and wait for the small sink mark. Wait a couple more seconds, then tap the sprue plate with a wooden stick (Gregor’s is wrapped in leather). The cut should leave a clean, flat base. Smeared bases: you cut too soon. Sprue cuts hard: you waited too long. Bases not filled out: pour with more pressure (hold the mould closer to the spout or open the spout more), and pour enough lead to keep one big continuous sprue. A big sprue keeps the mould and pins hot. Can’t find the rhythm? Fill the mould, count to 3, open the sprue plate, count to 3, open the mould and dump. Repeat. Opening the mould With rifle HP moulds, wait a couple of seconds after cutting the sprue, then turn the mould upside down and tap on the bolt on the handles. Let the tapping open the mould first, then help with the handles. This also pushes the side pins out. MP Crammer-style pins pull the bullets out of the cavities as the mould opens. At the right temperature the bullets fall off the pins by themselves. If not (mostly with a blank FP pin), tap the handle bolt a couple of times. If it takes more than a few taps, the mould and pins are too cold. Watch the sprue and the bases Your casting tempo controls the mould and pin temperature more than the alloy temperature does. The sprue tells you where you are: After preheating and a few pours, the sprue puddle stays liquid for a couple of seconds. About 3 seconds to harden: you’re ready to cast. Tilt the mould after 2 seconds and the sprue still pours off like water; after 3 it doesn’t. 4 seconds or more: slow down, cool the mould, or lower the alloy temperature. Below 550F / 290C the furnace spout may freeze; above 750F / 400C the surface oxidizes quickly. Stay in the zone: keep your cadence and inspect the bullets only after you finish. Each mould has its own “preferences”, so note the alloy temperature, hot plate setting and preheat time for every mould. Alternate the casting direction Pouring hot alloy in the same direction in a 4 or 6 cavity mould creates hot and cold sections. The last filled cavity is usually the hottest and can smear. Alternate front-to-back and back-to-front. Watch the bases and slow down if needed. Cool a hot part of the mould with a wet cloth. Lube the sprue plate while casting Not strictly necessary, but it reduces wear and removes small lead particles. About 4–5 times per hour

Free Worldwide shipping

On all orders above €399

Easy 30 days returns

30 days money back guarantee

International Warranty

Offered in the country of usage

100% Secure Checkout

Visa / MasterCard / Maestro