Filter products No products found!
Molds category
Choose mold type
Bullet base
Choose your bullet base profile
Caliber as cast
Use 0.001 or 0.002 inch over your bore size
Material
Choose your favorite mold material
Number of cavities
Choose no. of cavities
Other Categories
Handles, spare parts....

5,52 mm air pellet – 8 cavity mold

5,52 mm air pellet – 8 cavity mold

4.71 out of 5
(24 customer reviews)
SKU: 10186 Categories: , ,

 72.25

    • Mold will cast 5.52 mm diam. with wheel weights alloy (may vary – depends on alloy)
    • 35 grains (may vary – depends on alloy)
    • Lenght of pellet is 10.8 mm
    • 8 cavity
    • Steel sprue plate
    • Hardened steel alignment pins
    • Allen keys  included
    • Use LEE 6 cavity handle or MP mold handles (NOT included)

    See our product pictures in gallery

2 in stock

Compare

Additional information

Caliber (As cast)

5.52 mm

Handles included?

No

Material

Aluminum

Number of cavities

8 cavities

Pb-Bb-Gc-Hb

Bevel base

Description

  • Mold will cast 5.52 mm diam. with wheel weights alloy (may vary – depends on alloy)
  • 35 grains (may vary – depends on alloy)
  • Lenght of pellet is 10.8 mm
  • 8 cavity
  • Steel sprue plate
  • Hardened steel alignment pins
  • Allen keys  included
  • Use LEE 6 cavity handle or MP mold handles (NOT included)

See our product pictures in gallery

24 reviews for 5,52 mm air pellet – 8 cavity mold

4.7
4.71 out of 5
Based on 21 reviews
  1. 5 out of 5

    Donald (verified owner)

    Just started using this mold, it is a very fine/good mold,
    takes a bit to bring up to proper temperature and will make a lot of pellets in a hurry.

    Please bring out a 177 cal mold – 10.5 + grains of the same design and you’ll own the .177 mold market, as NO ONE makes a .177 pellet casting mold.

    If possible also add a HP feature to these caliber molds.

  2. 5 out of 5

    Derek (verified owner)

    They really shoot extremely accurate. At 50m I can put 5 rounds into a 20cm grouping with ease.

  3. 4 out of 5

    Anonymous (verified owner)

    I should like to use it for a year first, then do a full review also I have the 6,35 mould I have made the fools error of putting the wrong parts together ie the 5.5 handle half with the 6.35 they do go together but not good for the airgun. lol this is my fault not the mould. please give me the opportunity to review this again in a years time.

  4. 2 out of 5

    Darrell (verified owner)

    The mold was of good quality but the diameter of pellet is not compatible. I contacted the supplier and sent an email with picture and dimensions but still no reply – so far not very impressed with the service. Again I will state the quality of the mould is very nice. I have continued to experiment with this bullet. I have used a small amount of lube equal to Eley target 22 ammo. The slug now fits nicely in the chamber. I have the FX impact setup for 950fps (I’ve experimented with velocities from 750 -950) and the slug does not perform well at all it will not group and shoots sometimes 12 inches off at 50 yards. Also I found that it tumbles and I can hear it whistle through the air when this happens. I do not blame this on the mould or slug – it just isn’t compatible with the FX new liner (my conclusion maybe because of the design and length is needs a tighter rifling twist). I wish it did shoot well because I like the look of the slug and the quality from the mould. My primary reason for a low score is I have yet heard back from the supplier from the time I sent my data. It was a $120 lesson.

  5. 5 out of 5

    Denis (verified owner)

    Exzellent Service!

Add a review

Cancel