HP (Hollow points) Molds
Showing 1–16 of 119 results
-
311-140 SledgeHammer, Hollow Point (Multi Choice) – No lube groove
150.94$120.75$- cast .311 diam with wheel weights alloy (may vary – depends on alloy)
- HP Small 142 grains, Large 140Grains
- 147 grains solid
- 0.400″ meplat to crimp groove
- for heavy duty 32 magnum loads, 32-20’s and the new 327 Federal. Shows utility in the 300BO, 30-30, 30 Carbine and 308 and 30-06 Plinkers
-
314-140 SledgeHammer, Hollow point (multi choice)
80.83$ – 120.75$- cast .314 or .311 (choose) diam with wheel weights alloy (may vary – depends on alloy)
- HP Small 138 grains, Large 135 Grains
- 141 grains solid
- 0.400″ meplat to crimp groove
-
314-640 – 100 grain hollow point mold (Multi choice)
80.83$ – 120.75$- cast .314 diam with wheel weights alloy (may vary – depends on alloy)
- 100 grains hollow points
- 106 grain solid
-
314-640 Hollow point, 115 Grain Mold (Multi choice)
80.83$ – 120.75$- cast .314 diam with wheel weights alloy (may vary – depends on alloy)
- nose to crim groove .3645 inch
- 115 grains hollow points
- 121 solid
-
327 Joulnir, Hollow point mold (multi choice)
80.83$ – 120.75$- cast .314 diam with wheel weights alloy (may vary – depends on alloy)
- HP Cup 126 grains, Large 123 Grains
- 130 grains solid
- 0.297″ meplat to crimp groove
- Suitable for the 32 H&R or 327 Fed. Magnum handguns or rifles
-
358-200 RCBS (.360cal), Hollow point gas check, 2 cavity mold
101.03$80.83$- Cast .360cal. bullets
- Solid = 202 grain, blank pin for flat nose
- Large HP 195 gn , small HP 199 gn
-
358-429 (.360 cal) Keith, Hollow Point Gas check 4 Cavity Mold
150.94$120.75$- Cast .358 cal. bullets
- See picture for pins and weight
-
358-429 Keith (.360 cal.), Hollow point Plain base 4 cavity mold
150.94$120.75$- Cast .360 cal. bullets
- See picture for pins and weight
-
358-429 Keith, Hollow point 2 cavity mold (GC or PB)
101.03$80.83$- Cast .358 or .360 cal. bullets
- See picture for pins and weight
-
358-640 Hollow Point Gas Check, 2 Cavity Mold
101.03$80.83$- Cast .358 cal. bullets
- Solid = 96 gr., large/penta hp = 87 gr
- Large HP, penta HP, blank pin for flat nose
-
358-640 Hollow Point Gas check, 4 Cavity Mold
150.94$120.75$- Cast .358 cal. bullets
- Solid = 96 gr., large/penta hp = 87 gr
- Large HP, penta HP, blank pin for flat nose
-
358-640 Hollow point plain base, 4 cavity mold
150.94$120.75$- Cast .358 cal. bullets
- Solid = 96 gr., large/penta hp = 87 gr
- Large HP, penta HP, blank pin for flat nose
-
359 Hammer mold Hollow point (Multi choice)
80.83$ – 120.75$- Cast .360 cal. bullets
- See picture for weights
-
359-115 TC, Flat base, 8 cav.,Solid,Lube groove, Aluminum mold
101.03$80.83$- cast .359 diam with wheel weights alloy (may vary – depends on alloy)
- 115 grains solids (depends on alloy)
- for use in 9mm, too (easily sizes down)
- 8 cavity
-
359-640 Hollow point plain base, (Multi choice)
80.83$ – 120.75$- Cast .360 cal. bullets
- 170 grain solid
- 158 grains HP
- Meplat to crimp groove is 0.318″ and 0.357″.
- A dual use 357 boolit, the top crimp groove is for the short N-frame S&W 357 cylinders and the bottom crimp groove is for the 38 Special and long 357 Mag cylinder wheel guns.
-
360-640 Hollow point, 2 cavity mold
101.03$80.83$- Cast .360 cal. bullets
- 155 grain solid
- 140 grain HP