Shop
Hint! Use Search or filter to find our products.Bullet casting equipment
Showing 1–16 of 271 results
-
.22 air rifle mold 8 cavity Aluminum mold
€ 105.00€ 84.00- Cast .224 diam with wheel weights alloy (may vary – depends on alloy)
- Included sizer – push thru
- 35 grains (depends on alloy)
- 8 cavity
-
.32 Wad cutter 8 cavity aluminum mold
€ 83.00€ 66.40- Cast .314 cal. bullets – 98 grain solid
-
.38 Wad cutter 8 cavity aluminum mold
€ 83.00€ 66.40- Cast .359 cal. bullets – 148 grain solid
-
.678 Round ball, 2 cavity brass mold
€ 83.00€ 66.40- Cast .678 round ball (for use with wad 12ga.)
- 2 cavity
- Brass mold
-
.732 Round Ball, 2 Cavity Brass Mold
€ 83.00€ 66.40- Cast .732 round ball (for Full bore 12ga.)
- 2 cavity
- Brass mold
-
311-140 SledgeHammer, Hollow Point (Multi Choice) – No lube groove
€ 124.00€ 99.20- cast .311 diam with wheel weights alloy (may vary – depends on alloy)
- HP Small 142 grains, Large 140Grains
- 147 grains solid
- 0.400″ meplat to crimp groove
- for heavy duty 32 magnum loads, 32-20’s and the new 327 Federal. Shows utility in the 300BO, 30-30, 30 Carbine and 308 and 30-06 Plinkers
-
314-140 SledgeHammer, Hollow point (multi choice)
€ 66.40 – € 99.20- cast .314 or .311 (choose) diam with wheel weights alloy (may vary – depends on alloy)
- HP Small 138 grains, Large 135 Grains
- 141 grains solid
- 0.400″ meplat to crimp groove
-
314-640 – 100 grain hollow point mold (Multi choice)
€ 66.40 – € 99.20- cast .314 diam with wheel weights alloy (may vary – depends on alloy)
- 100 grains hollow points
- 106 grain solid
-
314-640 Hollow point, 115 Grain Mold (Multi choice)
€ 66.40 – € 99.20- cast .314 diam with wheel weights alloy (may vary – depends on alloy)
- nose to crim groove .3645 inch
- 115 grains hollow points
- 121 solid
-
32 cal. 98 grain SWC bevel/flat base (multi choice)
€ 83.00€ 66.40- Cast .314, .315 or .316 cal. bullets (choose)
- 98 grain
-
327 Joulnir, Hollow point mold (multi choice)
€ 66.40 – € 99.20- cast .314 diam with wheel weights alloy (may vary – depends on alloy)
- HP Cup 126 grains, Large 123 Grains
- 130 grains solid
- 0.297″ meplat to crimp groove
- Suitable for the 32 H&R or 327 Fed. Magnum handguns or rifles
-
356-115 Bevel Base, 8 Cavity Aluminum Mold
€ 83.00€ 66.40- cast .359 diam with wheel weights alloy (may vary – depends on alloy)
- 115 grains solid
-
356-115 flat base, 8 cavity aluminum mold
€ 83.00€ 66.40- cast .359 diam with wheel weights alloy (may vary – depends on alloy)
- 115 grains solid
-
356-115 Flat Base, 8 Cavity Aluminum Mold, NO lube groove
€ 83.00€ 66.40- cast .359 diam with wheel weights alloy (may vary – depends on alloy)
- 120 grains solid
-
356-135, Flat base, aluminum, 6 cavity mold
€ 83.00€ 66.40- Cast .359 cal. bullets
- 135 grain
- No problem sizing down to .356
-
356/359-125 Flat Round Nose, Flat Base, 8 Cavity Aluminum No Lube Groove Mold
€ 83.00€ 66.40- cast .356 to .359 diam with wheel weights alloy (may vary – depends on alloy)
- 125 grains solids
- for use in 9 mm, too.